UA

A painting robot you do not have to reprogram for every part

Inducoat is an engineering startup from Kharkiv, Ukraine. We are developing a cell where a 3D scanner, our own software and an industrial robot paint a part from its scan: toolpaths are calculated automatically.

Open Inducoat Studio

R&D stage: the architecture of the cell is designed, the physical system is not built yet.

Simulation
The concept visualised in Inducoat Studio. A browser simulation, not footage from a factory.
KharkivUkrainian engineering team: own software, equipment integration, support
R&DThe architecture of the cell is designed, there is no physical system yet
StudioAn interactive concept demo that runs in the browser and works offline

What we aim to achieve

These are design goals and expected effects. They can only be confirmed on physical equipment, and that is what we plan to do in pilots.

Less manual programming

Toolpaths are calculated from the scan of the part instead of being written by hand for every new part.

Less coating material used

Passes follow the elements of the part, so the spray does not work in empty space. Sensors track material consumption.

More stable coating

The same settings for the same parts reduce thickness scatter and the need to repaint.

Faster changeover

A new part means a new scan, not a new program.

People outside the spray zone

Less worker contact with the aerosol. Ventilation, explosion protection and guarding remain mandatory under the regulations.

Local support

Service by a Ukrainian engineering team, with no dependence on expensive foreign service.

We give no savings percentages or payback periods: only a pilot at a real plant can show them.

Painting depends on a few people and on manual setup

Typical problems at plants that paint the same parts every day.

Not enough painters

Skilled painters are scarce, and training a new one takes months.

Labour keeps getting more expensive

Skilled work costs more every year, and the result depends on one person.

Coating quality varies

Thickness and evenness change from shift to shift. Defects show only after curing.

Paint misses the part

Part of the coating material is lost as overspray, especially on open-work parts.

Changeover takes time

A new part means a new program or new manual setup.

Expensive foreign service

Servicing imported equipment is expensive and slow.

For plants that paint the same thing again and again

  • MDF fronts and furniture
  • Metalworking
  • Fences and steel structures
  • Industrial enclosures, cabinets, equipment
  • Automotive parts
  • Other plants with repeated painting

How the cell will work

This is a design scheme. The physical cell is not built yet, so below is what we are developing, not test results.

First version: a stationary six-axis industrial robot and liquid coating materials.

  1. The operator places the part in the work zone.
  2. A 3D scanner captures the geometry of the part.
  3. An industrial computer processes the point cloud.
  4. Our software calculates toolpaths and painting parameters for this geometry.
  5. The robot's own controller runs the motion program.
  6. A PLC coordinates the spray equipment and reads the pressure and flow sensors.
  7. The system stores parameters, recipes and a log of every cycle.

Works locally

No required internet connection.

Safety stays separate

The industrial safety circuit does not depend on our software.

The robot controller stays

We do not replace the stock control system. We add a layer for geometry and path planning.

Ways we can work with your plant

The project is at R&D stage. Terms, timing and cost are agreed for each plant.

Inducoat System

A new turnkey robotic painting cell: equipment, our software and integration on your line.

Inducoat Retrofit

Upgrading compatible robotic installations. We add scanning, path planning and digital records, and your working manipulator stays.

Engineering & Integration

Custom automation projects for your plant.

Service & Maintenance

Equipment service and support by a Ukrainian engineering team.

Rental / Leasing

Rental and leasing of robotic systems.

Inducoat Studio: try the concept now

Pick a part, set its size, scan it, plan the toolpaths and watch it being painted in 3D. Studio shows our idea before the physical cell exists. The Studio interface is in Ukrainian.

  • Part type and size: cabinet, MDF front, fence section
  • Simulated scanning and point cloud
  • Robot toolpaths and a coating thickness map
  • Manual versus robotic painting, a scenario-based coating material estimate
  • Presentation and engineering modes
Launch Inducoat Studio
A KUKA KR 16-2 robot above a cabinet lid in a paint booth, as seen in Inducoat Studio
A laser scanner on a tripod scanning a cabinet
Scanning
Working passes and transitions of the robot over the part
Toolpaths
The robot paints a side face of the cabinet
Painting
Film thickness map on the cabinet faces
Thickness map

Studio is a separate demo. It is not connected to real equipment, does not control a robot and does not prove the throughput or accuracy of the future cell. An offline version without internet is available (about 1 MB).

What we aim to achieve

These are design goals and expected effects. They can only be confirmed on physical equipment, and that is what we plan to do in pilots.

Less manual programming

Toolpaths are calculated from the scan of the part instead of being written by hand for every new part.

Less coating material used

Passes follow the elements of the part, so the spray does not work in empty space. Sensors track material consumption.

More stable coating

The same settings for the same parts reduce thickness scatter and the need to repaint.

Faster changeover

A new part means a new scan, not a new program.

People outside the spray zone

Less worker contact with the aerosol. Ventilation, explosion protection and guarding remain mandatory under the regulations.

Local support

Service by a Ukrainian engineering team, with no dependence on expensive foreign service.

We give no savings percentages or payback periods: only a pilot at a real plant can show them.

Where we are

  1. Done

    Inducoat Studio

    The interactive demo works in the browser and offline.

  2. Now

    Physical cell

    The architecture is designed. The system is not built yet.

  3. Next

    A pilot at a real plant

    It will confirm coating material savings, throughput and payback. Until then we do not promise them.

From the blog

Short technical notes on painting, coating materials and upgrading installations.

All articles

Questions from plant managers

Do we have to replace our robot?

No. For compatible robotic installations there is Inducoat Retrofit: we add scanning, path planning and digital records, and your working manipulator stays. The robot's own controller always runs the motion program.

What about safety?

The industrial safety circuit does not depend on our software. The operator works outside the spray zone, but ventilation, explosion protection and guarding remain mandatory under the regulations.

Does the line need internet?

No. We design the system to work locally, without a required network connection.

Which parts and materials will it handle?

The first version will work with liquid coating materials on a stationary six-axis robot. It suits parts that are painted in repeated runs: MDF fronts, fences, enclosures, steel structures, automotive parts. The limits depend on the specific installation.

How much does it cost and when does it pay back?

It depends on the part, volumes and existing equipment. We give no figures without a calculation for your plant, so a pilot is the way to get a real answer.

Who will service the equipment?

A Ukrainian engineering team from Kharkiv: software, integration and support in one team.

Is there a working installation yet?

No. The project is at R&D stage: the architecture of the cell is designed, the physical system is not built yet. Inducoat Studio shows the concept but does not control any equipment.

Let us test the technology on your part

For plants considering robotic painting or an upgrade of an existing robot. Tell us briefly about your part and coating, we will get in touch and discuss the pilot format. No payments, no obligations.

  • Your part type and coating
  • Whether your plant already has an industrial robot
  • A contact, used only to discuss the pilot

The request takes about two minutes

The form opens in a Tally window and is in Ukrainian. Your data is used only to contact you about the pilot, see how it is handled.